RDA'S

VANDY VAPE MAZE 24MM BF RDA

The Vandy Vape Maze Sub Ohm BF RDA is a squonk compatible 24mm RDA (Rebuildable dripping atomiser) - that uses an innovative new coil system ideal. We recommend it for advanced users who are just beginning to use RDAs.

What sets the Maze apart from other rebuildables, is the Maze BF Vape Coil. The 0.2 Ohm coils turn the Maze into a mix between a sub ohm tank and an RDA. With it’s unique stove top design, the coil is prewicked with cotton, is simple to screw in and has a firing range of between 50 - 100W.

When used with the pre-installed bf (bottom feeding) pin, the Vandy Vape Maze is primed by simply squeezing your squonk bottle, allowing liquid to travel through the BF (Bottom Feed) pin and into the 5mm approx. juice well.

The Maze Sub Ohm BF RDA, can be used with standard boxes by installing a 510 pin. In the kit there is a 510 Pin and Refill Tube, which when installed in the rda allow it to be used as a standard RDA… with a twist.

Rather than dripping directly onto your coil, you drip your eliquid into the Refill Tube where it will flow directly into the juice well. It has been reported that this may reduce the capacity of the amount of liquid in the well, down to 3mm.

There are five airflow grids located at the top of the Vandy Vape Maze RDA, allowing you to control airflow efficiently, for a tighter draw or cloud chasing.

Overall, this is an inventive and well-designed RDA that can be customised for a unique vaping experience.

Contains

  • 1 x Vandy Vape Maze Sub Ohm BF RDA
  • 1 x Squonk Pin (pre-installed)
  • 1 x 510 Pin
  • 1 x Refill Tube
  • 2 x 0.2 Ohm Maze Coils

Features

  • Unique Coil Design
  • Easy to Drip
  • Squonk Compatible
  • Adjustable Airflow

Important information regarding Pre-made Coils and Rebuildables:

This product is designed for experienced users, and for those possessing an ohm reader or multimeter to test their coils on.

This item requires a comprehensive understanding of the technicalities of vaping, along with knowledge of electronics and ohms law. We don’t advise any beginners to start rebuilding coils without speaking to us or a knowledgeable shop. We do not recommend using this kind of product with a mechanical mod of any kind.

A rebuildable coil must be tested carefully on an ohms reader before it is used on a device. Not testing this properly may present a safety risk for the user, and no new coils should be used on an electronic vaping device until the coil is known to be safe.

ASVAPE AIM-9 24MM RDA VAPE TANK

The Asvape AIM-9 RDA is a 24mm RDA (Rebuildable Dripping Atomiser) that features a Velocity Style Build Deck, bottom airflow and Stainless Steel construction. The spacious deck makes the AIM-9 easy to build on. This rebuildable atomiser is intended for advanced users only.

With a solid Stainless Steel construction not only is the AIM-9 hard wearing, it has a clean aesthetic with detailed engraving and a generously sized 0.85mm juice well. Smooth machining make this RDA easy to disassemble and clean.

Gold plating on the deck and 510 Pin give this device increased conductivity for improved heating properties. The option of either a wide-bore PCM drip tip or 510 drip tip adaptor allow for increased flavour and the option to fit a custom drip tip.

The 22mm Two Post Velocity Style Build Deck is spacious enough to accommodate a variety of coil types including premade coils, please note that only dual coil configurations are compatible with the AIM-9. The adjustable bottom airflow allows for greater control of airflow allowing for a breezy direct to lung inhale or a restricted mouth to lung vape.

Overall, the Asvape AIM-9 is a robust yet stylish RDA that combines ease of use with large cloud production and adjustable airflow.

Contains:

  • 1 x AIM-9 RDA
  • 1 x Accessories Bag
  • 1 x Spares Kit
  • 1 x 510 Drip Tip Adaptor
  • 1 x Instruction Manual

Features:

  • 24mm RDA
  • Stainless Steel Construction
  • Gold Plated Deck and 510 Pin
  • Two Post Velocity Build Deck
  • 0.85mm Juice Well
  • Wide Bore Drip Tip

Important information about Rebuildable Dripping Atomisers:

This product is designed for experienced users, and for those possessing an ohms reader or multimeter to test their coils on. This device requires a comprehensive understanding of the technicalities of vaping, along with knowledge of electronics and Ohm’s law.

We don’t advise any beginners to start rebuilding coils without speaking to a knowledgeable shop. A rebuildable coil must be tested carefully on an ohms reader before it is used on a device. Not testing this properly may present a safety risk for the user, and no new coils should be used on an electronic vaping device until the coil is known to be safe

£0.00
VANDY VAPE BONZA 24MM RDA

The Vandy Vape Bonza RDA is the result of a collaboration between a Chinese vape company and vaping personality, The Vaping Bogan.

The Bonza is a 24mm diameter RDA that offers a wide airflow, and space for both single and dual coil builds, with the deck featuring a fixed screw clamp post. Both a 510 pin as well as a Bottom Feeding (BF) pin are included for those that squonk, with the bottom feeding directly into side juice wells.

Along with the BF pin, both a 16mm Delrin Drip Tip and a slightly larger 17.5mm Ultem Drip Tip are included alongside the Bonza's decorative food-grade Resin Drip Tip that's preinstalled.

Contains:

  • 1 x Vandy Vape Bonza RDA
  • 1 x 16mm Delrin Drip Tip
  • 1 x 17.5mm Ultem Drip Tip
  • 1 x Accessories Bag
  • 1 x User Manual

Features:

  • 24mm Diameter
  • Wide Airflow
  • Both Single & Dual Coil Builds
  • Fixed Screw Clamp Post
  • Bottom Feeding Pin
  • Resin, Delrin, and Ultem Drip Tips Included

Important information about Rebuildable Dripping Atomisers:

This product is designed for experienced users, and for those possessing an ohms reader or multimeter to test their coils on. This device requires a comprehensive understanding of the technicalities of vaping, along with knowledge of electronics and ohms law.

We don’t advise any beginners to start rebuilding coils without speaking to a knowledgeable shop. A rebuildable coil must be tested carefully on an ohms reader before it is used on a device. Not testing this properly may present a safety risk for the user, and no new coils should be used on an electronic vaping device until the coil is known to be safe.

DIGIFLAVOR DROP 24MM RDA

The Digiflavor Drop RDA has been designed by the Vapor Chronicles and is the latest Digiflavour RDA. It features 4 large post holes and duel airflow which allows for a bottom airflow experience with no leaking.

The airflow design allows for precise control and an ultra smooth, whistle free vaping experience. The post placement and large spacious juice well allow for perfect liquid disbursement whatever your vaping style.

The Drop RDA is supplied with two different sized 810 drip tips and a 510 drip tip adaptor, you will find a standard 510 and raised BF squonk 510 pin.

Contains:

  • 1 x DigiFlavor Drop RDA
  • 2 x 810 Drip Tips
  • 1 x 510 Drip Tip Adaptor
  • 1 x Allen Key
  • 1 x User Manual
  • 1 x Bottom Feed Positive Pin

Features:

  • 24mm Diameter
  • Dual Airflow
  • Single, Dual, Triple and Quad Coil builds
  • Removed Gold Plated positive and negative posts
  • Deep and Spacious Juice well
  • Internal raised BF Squonk Pin included.

Important information about Rebuildable Dripping Atomisers:

This product is designed for experienced users, and for those possessing an ohms reader or multimeter to test their coils on. The device requires a comprehensive understanding of the technicalities of vaping, along with knowledge of electronics and ohms law.

We don't advise any beginners to start rebuidling coils without to a knowledgeable shop. A rebuildable coil must be tested carefully on an ohms reader before it is used on a device. Not testing this properly may present a safety risk for the user, and no new coils should be used on an electronic vaping device until the coil is known to be safe.

VANDY VAPE ICONIC 24MM RDA

Vandy Vape Iconic RDA is a 24mm RDA (Rebuildable Dripping Atomiser), created in collaboration with Mike Vapes and is an upgrade to earlier Icon RDA from the Vandy Vape Range. With a host of improvements including newly designed airflow and post clamp design, this atomiser is ideal for high wattage vaping.

The two post clamp build deck is large allowing for straightforward installation of a variety of coil types, including premade coils. This, plus the deep juice well make this 24mm RDA easy to drip on, once wicked with cotton.

The unique airflow design distinguishes the Iconic RDA from other models. By utilising an angled tubular bottom airflow system, the user will experience not only increased flavour and cloud production, but also minimised leakage. On top of this there are also two cyclops airflow vents allowing for a greater degree of adjustment and control.

Included within the kit is a standard 510 pin and also a BF (Bottom Feeding) Pin allowing the Vandy Vape Iconic RDA to be used in combination with a squonk box.

Overall, the Iconic RDA is an incredibly versatile piece of vape hardware, with maximum airflow allowing for huge vapour production and flavour.

Contains

  • 1 x Vandy Vape Iconic 24mm RDA
  • 1 x 510 Pin (pre-installed)
  • 1 x BF (Bottom Feeding) Pin
  • 1 x Resin Drip Tip (pre-installed)
  • 1 x Delrin Doc Tip
  • 1 x Frosted Doc Tip
  • 1 x Spares Pack

Features

  • Two Post Clamp Build Deck
  • 24mm Diameter
  • Deep Juice Well
  • Unique Airflow
  • Squonk Compatible

Important information about Rebuildable Dripping Atomisers:

This product is designed for experienced users, and for those possessing an ohms reader or multimeter to test their coils on. This device requires a comprehensive understanding of the technicalities of vaping, along with knowledge of electronics and Ohm’s law.

We don’t advise any beginners to start rebuilding coils without speaking to a knowledgeable shop. A rebuildable coil must be tested carefully on an ohms reader before it is used on a device. Not testing this properly may present a safety risk for the user, and no new coils should be used on an electronic vaping device until the coil is known to be safe

COUNCIL OF VAPOR ROYAL HUNTER X 24MM RDA

The Council of Vapor Royal Hunter X RDA, is an upgrade to the previous versions of the Royal Hunter. This is a 24mm RDA (rebuildable dripping atomiser) that features a clamp build deck and a generously sized juice well. This is an RDA that has been described as spacious and easy to build on since it’s release, it is advised for advanced users only.

The Royal Hunter X RDA is made of durable, High Grade Stainless Steel promoting a cleaner taste when vaped. The build deck is a versatile, Dual Terminal Clamp Deck. The inclusion of clamps means a number of different coil build sizes are easy to install, including premade coils. Coils are secured via flat head screws which fit firmly into place to minimise movement.

The 24mm diameter RDA has a deep and wide juice well designed to minimise rewicking. The RDA’s airflow is slanted and allows for a greater degree of airflow control and also cloud production, enhanced by the wide bore drip tip. The airflow can be easily adjusted and allows the vaper to mount a single or dual coil build.

Overall, the Royal Hunter X RDA provides vapers with not only a large space to build coils on but an equally large juice well. Combining ease of use with functionality and maximum airflow.

Contains:

  • 1 x Royal Hunter X RDA
  • 1 x Spares Kit
  • 1 x User manual

Features:

  • 24mm Diameter
  • Stainless Steel Construction
  • Deep Juice Well
  • Dual Terminal Clamp Deck
  • Adjustable Airflow

Important information about Rebuildable Dripping Atomisers:

This product is designed for experienced users, and for those possessing an ohms reader or multimeter to test their coils on. This device requires a comprehensive understanding of the technicalities of vaping, along with knowledge of electronics and Ohm’s law.

We don’t advise any beginners to start rebuilding coils without speaking to a knowledgeable shop. A rebuildable coil must be tested carefully on an ohms reader before it is used on a device. Not testing this properly may present a safety risk for the user, and no new coils should be used on an electronic vaping device until the coil is known to be safe

£26.99
VANDY VAPE BERSERKER MTL RDA

The Vandy Vape Berserker Mini MTL RDA, is a mouth to lung RDA (Rebuildable Dripping Atomiser) that has a unique aesthetic and a level of customisability that is unseen in most rebuildables. Featuring Stainless Steel construction, an 18mm diameter and single coil build capabilities, this RDA is advised for advanced users only.

With an 18mm diameter the Berserker is smaller than most standard RDAs, this is intentional as a smaller diameter equals a smaller chamber, giving the user a consistent mouth to lung draw along with increased flavour. For those worried about aesthetics, each kit comes with a 22mm and 24mm Beauty Ring allowing the RDA to sit flush on most vape mods.

The Berserker MTL RDA features a clamp deck, designed for single coil builds. This build deck allows your coil to be mounted easily despite the size, there’s also a specially designed correction tool included which allows the user to secure the coil while tightening the clamps.

What sets the Berserker apart from similar MTL RDAs is its airflow capabilities; as well as a standard adjustable airflow, there are also six airflow adaptors, each can slot into place under the build deck and allow complete customisation of your inhale for a tighter or looser draw.

The Heat Sink Drip Tip, combined with a drip shield and Ultem mouthpiece allows for a cooler vape without sacrificing on flavour. If that wasn’t enough, there is an extra BF (Bottom Feeding) Pin included with the kit, allowing you to transform the Berserker into a Squonk RDA.

Contains:

  • 1 x Vandy Vape Berserker MTL RDA
  • 1 x 22mm Beauty Ring
  • 1 x 24mm Beauty Ring
  • 1 x Coil Correction Tool
  • 1 x BF (Bottom Feeding) Pin
  • 6 x Airflow Adaptors
  • 1 x User Manual

Features:

  • 18mm Diameter
  • Squonk Compatible
  • Single Coil Build
  • Dual Post Clamp Deck
  • Mouth To Lung Inhale
  • Unique Adjustable Airflow

Important information regarding Pre-made Coils and Rebuildables:

This product is designed for experienced users, and for those possessing an ohm reader or multimeter to test their coils on.

This item requires a comprehensive understanding of the technicalities of vaping, along with knowledge of electronics and ohms law. We don’t advise any beginners to start rebuilding coils without speaking to us or a knowledgeable shop. We do not recommend using this kind of product with a mechanical mod of any kind.

A rebuildable coil must be tested carefully on an ohms reader before it is used on a device. Not testing this properly may present a safety risk for the user, and no new coils should be used on an electronic vaping device until the coil is known to be safe.

WOTOFO RECURVE 24MM BF RDA

The Wotofo Recurve RDA is a 24mm RDA (Rebuildable Dripping Atomiser) that has been designed and created in collaboration with Mike Vapes. Unique airflow, concave design and single coil build deck really set this RDA apart. The Recurve is intended for advanced users only.

The Recurve has been designed for enhanced flavour, The Stainless Steel construction promotes a cleaner taste for a purer vape. The concave shape of the top cap allows for a greater concentration of flavour compared to standard RDAs. The 810 drip tip has the same curvature as the Recurve itself, again creating a deeper flavour.

The postless build deck has been designed for single coil builds only, the coil ports are large enough to support a variety of wire types, including premade coils. The Recurve features a U-shape design with dual six-hole airflow that matches up with the top cap; this adjustable airflow not only increases flavour it reduces spit back and leaking when being used. 

Coil builders and direct to lung vapers looking to get more out of their eliquid should consider the Wotofo Recurve for a deeper flavour.

Contains:

  • 1 x Wotofo Recurve RDA
  • 1 x BF Pin (pre-installed)
  • 1 x Standard 510 Pin
  • 1 x Accessories Bag
  • 1 x Spares Kit
  • 3 x Prebuilt Coils
  • 1 x Instruction Manual

Features:

  • 24mm Diameter
  • Stainless Steel Construction
  • Single Coil Builds Only
  • Unique Curve Design
  • Adjustable Airflow

Important information about Rebuildable Dripping Atomisers:

This product is designed for experienced users, and for those possessing an ohms reader or multimeter to test their coils on. This device requires a comprehensive understanding of the technicalities of vaping, along with knowledge of electronics and Ohm’s law.

We don’t advise any beginners to start rebuilding coils without speaking to a knowledgeable shop. A rebuildable coil must be tested carefully on an ohms reader before it is used on a device. Not testing this properly may present a safety risk for the user, and no new coils should be used on an electronic vaping device until the coil is known to be safe.

£24.99
UWELL FANCIER RTA RDA VAPE TANK

The Uwell Fancier RTA / RDA is a unique rebuildable atomiser intended for advanced users. It has a 24mm diameter, two post Velocity Build Deck and an eye catching colour scheme. This piece of vape hardware really stands out due to the fact that by changing the top cap you can quickly transform it into an RDA (Rebuildable Dripping Atomiser) or RTA (Rebuildable Tank Atomiser).

In RTA mode, this device features a 2ml capacity tank, with a wide juice port that is conveniently located at the top of the tank and is accessible by removing the drip tip and cap. The two post Velocity Deck will fit a variety of coil wire types - including premade coils, but supports dual coil builds only. The cotton wicks are fed upwards into the tank that sits atop the deck allowing juice to flow downwards for consistent wicking.

By removing the top cap and glass section, then replacing it with the alternate top cap - the Uwell Fanicer is transformed into a capable RDA with a 810 drip tip. Still utilising the Velocity Deck there is a generously sized juice well and bottom airflow, that has four adjustable airflow slots for a greater degree of control over the inhale and flavour you’ll experience.

When in RDA mode, the Fancier can be fitted with the BF (Bottom Feeding) Pin that comes with the kit, making it squonk compatible.

Overall, the Uwell Fanicer is one of the most versatile rebuildables available on the market today - unique stylings and design make it ideal for advanced users looking to experiment and customise.

Contains:

  • 1 x Uwell Fancier RDA / RTA
  • 1 x BF Pin
  • 1 x RDA Top Cap
  • 1 x Spare Glass Section
  • 1 x Spares Kit
  • 2 x Premade Coils
  • 1 x User Manual

Features:

  • RTA Mode
  • 2ml Tank
  • 24mm Diameter
  • Top Fill
  • RDA Mode
  • Squonk Compatible
  • Two Post Velocity Deck
  • Adjustable Bottom Airflow

Important information about Rebuildable Atomisers:

This product is designed for experienced users, and for those possessing an ohms reader or multimeter to test their coils on. This device requires a comprehensive understanding of the technicalities of vaping, along with knowledge of electronics and ohms law.

We don’t advise any beginners to start rebuilding coils without speaking to a knowledgeable shop. A rebuildable coil must be tested carefully on an ohms reader before it is used on a device. Not testing this properly may present a safety risk for the user, and no new coils should be used on an electronic vaping device until the coil is known to be safe.

£34.99
DOTMOD PETRI V2 22MM RDA

The Dotmod Petri RDA V2 is a 22mm RDA (Rebuildable Dripping Atomiser) that includes a luxury finish and uses high quality materials. The Petri V2 features a unique build deck layout and adjustable airflow; this rebuildable atomiser is intended for advanced users only.

Quality machining and consistent build quality mean that this RDA is not only hard wearing it’s easy to assemble and disassemble. The Petri V2 features anodized aluminum construction. With gold plating on the terminal posts and build deck that increase heat conduction. Full PEEK insulation offers increased protection from overheating. Unique airflow slots allow the RDA to be adjusted to maximise flavour and cloud.

The build deck is a two post clamp deck, with one large elliptical hole on each post. This spacious deck allows for a variety of wire types to be used, including premade coils. Please note that the Petri V2 only supports dual coil builds. The post screws are easy to tighten and remove thanks to the knurling, a deep juice well provides you with ample room for eliquid.

Contains:

  • 1 x Petri V2 RDA
  • 1 x Spares Bag
  • 1 x Warranty Card

Features

  • 22mm Diameter
  • Two Post Deck
  • Dual Coil Builds Only
  • Adjustable Airflow
  • Gold Plated Deck and Posts

Important information regarding Pre-made Coils and Rebuildables:

This product is designed for experienced users, and for those possessing an ohm reader or multimeter to test their coils on.

This item requires a comprehensive understanding of the technicalities of vaping, along with knowledge of electronics and ohms law. We don’t advise any beginners to start rebuilding coils without speaking to us or a knowledgeable shop. We do not recommend using this kind of product with a mechanical mod of any kind.

A rebuildable coil must be tested carefully on an ohms reader before it is used on a device. Not testing this properly may present a safety risk for the user, and no new coils should be used on an electronic vaping device until the coil is known to be safe.

£49.99
HELLVAPE DEAD RABBIT 24MM RDA

The Hellvape Dead Rabbit RDA, is a collaboration between The Vaping Heathen and Hellvape. This is a 24mm RDA (Rebuildable Dripping Atomiser) that features a unique four post build deck and a generously sized juice well. This rebuildable atomiser is intended for advanced users only.

With hard wearing Stainless Steel construction the Dead Rabbit provides a cleaner flavour when vaped. The ‘Bunny Ear’ build deck is made up of four posts with a terminal on each, leaving plenty of room for various wire types, including premade coils. Coils can be secured with either the hex screws or flathead screws provided. This deck supports single and dual coil builds.

A 5mm deep juice well allows not only ample room for your cotton wick but also your eliquid. The Dead Rabbit features fully adjustable top airflow, allowing the user to control not only flavour and cloud production but also the inhale. A 810 Resin Drip Tip creates a cooler vape and there is also the option of an 810 Delrin Drip Tip and a 510 adapter for flavour chasers.

Gold-plating on the build posts and the firing pin allow for greater conductivity ensuring a faster ramp up and even distribution of heat. The Dead Rabbit is a squonk compatible RDA and features a BF (Bottom Feeding) Pin, which can be attached rather than the standard 510 Pin.

Contains:

  • 1 x Hellvape Dead Rabbit RDA
  • 1 x 510 Drip Tip Adapter
  • 2 x 810 Drip Tips
  • 1 x Gold-Plated 510 Pin (pre-installed)
  • 1 x Gold-Plated BF Pin
  • 1 x Spares Kit

Features:

  • 24mm RDA
  • Unique Four Post Deck
  • Adjustable Airflow
  • Single and Dual Coil Builds
  • Squonk Compatible
  • 5mm Juice Well

Important information about Rebuildable Dripping Atomisers:

This product is designed for experienced users, and for those possessing an ohms reader or multimeter to test their coils on. This device requires a comprehensive understanding of the technicalities of vaping, along with knowledge of electronics and Ohm’s law.

We don’t advise any beginners to start rebuilding coils without speaking to a knowledgeable shop. A rebuildable coil must be tested carefully on an ohms reader before it is used on a device. Not testing this properly may present a safety risk for the user, and no new coils should be used on an electronic vaping device until the coil is known to be safe.

CONGREVAPE DOGE V4 24MM RDA

The Doge V4 RDA by Congrevape, is a 24mm RDA (Rebuildable Dripping Atomiser) designed with customisation in mind. The kit comes with two 24K Gold-Plated build decks, allowing for a variety of coil builds. This is an RDA for advanced users and coils builders.

The first deck, is a 24K Gold-Plated Two Post Clamp build deck. It features 4mm clamping space and a 7mm Deep Juice Well. With a maximized build space, the sky’s the limit; allowing the user to install large flat single coil builds and dual coil builds. The clamp deck has internal springs to keep the clamps up when unscrewed for easier building. When you’ve finished building simply add your cotton wick and drip away.

The second deck, is a 24K Gold-Plated Four Post build deck, upgraded from the earlier versions of the Doge RDA. This deck has an 11mm Deep Juice Well and four equally sized post holes - with a single terminal per post. These posts can hold speciality, round, flat and even premade coils, while still allowing the user to create single or dual coil builds.

Both variations of deck also support a BF Pin (Bottom-Feeding Pin), which comes included in the kit - allowing the Congrevape Doge V4 to be used as a Squonk RDA. Alternatively the standard 510 pin also included can be used with either deck.

The Cyclops Air Flow on the Doge V4 has been laser cut to avoid noise when inhaling; the air holes are also fully adjustable for a tighter or looser draw. This is all topped of with a Ceramic 10mm Bore Drip Tip.

Contains:

  • 1 x Congrevape Doge V4 24mm RDA
  • 1 x 24K Gold Plated Four Post Build Deck
  • 1 x 24K Gold Plated Two Post Clamp Style Build Deck
  • 1 x 510 pin
  • 1 x BF Pin (Bottom-Feeding Pin)
  • 1 x 10mm Tapered Bore Ceramic 810 Drip Tip
  • 1 x Spare Parts Pack

Features:

  • 24mm Diameter
  • 24k Gold-Plated Build Decks
  • Single and Dual Coil Builds
  • Two Post Clamp Deck Option
  • Four Post Build Deck Option
  • Adjustable Cyclops Airflow

Important information about Rebuildable Dripping Atomisers:

This product is designed for experienced users, and for those possessing an ohms reader or multimeter to test their coils on. This device requires a comprehensive understanding of the technicalities of vaping, along with knowledge of electronics and Ohm’s law.

We don’t advise any beginners to start rebuilding coils without speaking to a knowledgeable shop. A rebuildable coil must be tested carefully on an ohms reader before it is used on a device. Not testing this properly may present a safety risk for the user, and no new coils should be used on an electronic vaping device until the coil is known to be safe.

DIGIFLAVOR M MESH PRO 25MM RDA

The Digiflavor Mesh Pro is an RDA (Rebuildable Dripping Atomiser), can utilise mesh coils - for a bespoke vaping experience. Please note that standard wound coils can also be used. This RDA is recommended for advanced users only.

The M Pro is 25mm in diameter and incorporates a deep juice well and a unique postless clamp build deck. What really sets this RDA apart, are the mesh coils. With three metal types included with the kit (Kanthal, Stainless Steel and Nichrome) the user has the option of a different vape experience for each. Mesh coils provide a quicker and more even heat, and allow for a larger cotton wick to be used.

The RDA also fits standard wound coils, with the option of both single and dual coil builds. For added versatility the Mesh RDA includes two drip tips, a wide bore 810 and a standard 510, with adaptor. What’s more the kit has the option of becoming squonk compatible with a BF (Bottom Feeding) Pin included, as well as a 510 pin.

Overall the Digiflavor Mesh Pro is a well designed and stylish vape device, for avid builders and flavour chasers alike.

Contains:

  • 1 x Digiflavor Mesh Pro RDA
  • 1 x 810 Drip Tip
  • 1 x 510 Drip Tip
  • 1 x Stainless Steel Mesh Coil
  • 1 x Kanthal Mesh Coil
  • 1 x Nichrome Mesh coil
  • 1 x 510 Pin
  • 1 x BF (Bottom Feeding) Pin
  • 1 x Spares Kit

Features:

  • 25mm Diameter
  • Dual Airflow
  • Postless Clamp Deck
  • Single and Dual Coil Builds
  • Mesh Coil Builds
  • Squonk Compatible

    Important information about Rebuildable Dripping Atomisers:

    This product is designed for experienced users, and for those possessing an ohms reader or multimeter to test their coils on. The device requires a comprehensive understanding of the technicalities of vaping, along with knowledge of electronics and ohms law.

    We don't advise any beginners to start rebuidling coils without to a knowledgeable shop. A rebuildable coil must be tested carefully on an ohms reader before it is used on a device. Not testing this properly may present a safety risk for the user, and no new coils should be used on an electronic vaping device until the coil is known to be safe.

    DOTMOD 24MM DOTRDA

    The DotRDA by dotMod, like the rest of their products, is a high-quality piece of kit that's designed to be both practical and stylish. It features a 24K gold-plated brass deck with huge clamping space, along with a revolutionary new spring-loaded design that features a single post.
Both cap and barrel are made from anodized aluminium, with interchangable pins that allow for squonk vaping. The DotRDA can be completely dissassembled without the use of a screwdriver using dotMod's patented dotKey tool.

    Contains:

    • 1 x dotMod 24mm DotRDA
    • 1 x Ultem Drip Tip
    • 1 x DotKey
    • 1 x Extras (Fused Clapton Coils, Spare O-rings, Squonk Pins)

    Specifications:

    • Revolutionary new spring loaded single post design 
24K gold plated brass deck
    • Adjustable airflow control 
Anodized aluminum barrel and cap
    • Interchangeable center pins for Squonking
    • 3.9mm x 1.5mm Clamping space 
 
    • Easy-drip three piece design 
4.8mm Deep Juice Well
    • Can be completely built or disassembled with the dotKey

    Important information about Rebuildable Dripping Atomisers:

    This product is designed for experienced users, and for those possessing an ohms reader or multimeter to test their coils on. This device requires a comprehensive understanding of the technicalities of vaping, along with knowledge of electronics and ohms law.

    We don’t advise any beginners to start rebuilding coils without speaking to a knowledgeable shop. A rebuildable coil must be tested carefully on an ohms reader before it is used on a device. Not testing this properly may present a safety risk for the user, and no new coils should be used on an electronic vaping device until the coil is known to be safe.

    Top

    Panel Tool
    Float header
    Float topbar
    Default Boxed Large Boxed Medium
    Header Default Header One