DOTMOD

DOTMOD DOTSQUONK BF SQUONK MOD

The DotSquonk by DotMod is a mechanical vape device. This is a high end squonk box, designed to be used with a bottom feeding RDA only. This box has an air of elegance about it due to its high polish finish and detailing; the squonk bottle installed in the device has a 12ml fill capacity and is very flexible. As this is a mechanical device we recommend it to be used by very experienced vapers only.

The DotSquonk is powered by a single 18650 vape battery or a 20700 vape battery (both sold separately) and is simple to operate with it's one button system. This is combined with a large power output and minimal ramp up time to ensure best performance. With performance in mind DotMod have included a 24k gold plated centre pin for increased conductivity and faster heating.

If you are looking for a collector’s piece that is as functional as it is stylish then look no further than the DotSquonk.

Contains

  • 1 x DotSquonk Box Mod
  • 2 x Removable Doors
  • 1 x Squonk Bottle
  • 1 x Certificate of Authenticity

Features

  • Mechanical Mod
  • Requires a 18650 or 20700 Vape Battery (sold separately)
  • High End Device
  • Anodised Aluminium Finish

MECH MOD ALERT

Top Tips - Mechs Are Intended for Advanced Users ONLY

  • We don't recommend building below 0.2Ω
  • Always use an Ohms Reader to check resistance before using
  • For low resistance builds use high amp batteries
  • Ensure your battery wrap is intact
  • Ensure your locking switch is activated when not in use
  • Store your batteries safely in a case, never loose
  • Use a dedicated charger for batteries
  • Never leave charging batteries unattended
  • Dispose of batteries responsibly
  • Avoid short circuits by ensuring coils are installed as per manufacturer instructions

Battery / Amperage Guide (Do Not Exceed Limits)

  • 1.0ohms - 4.2A Amp Draw
  • 0.9ohms - 4.6A Amp Draw
  • 0.8ohms - 5.2A Amp Draw
  • 0.7ohms - 6.0A Amp Draw
  • 0.6ohms - 7.0A Amp Draw
  • 0.5ohms - 8.4A Amp Draw
  • 0.4ohms - 10A Amp Draw
  • 0.3ohms - 14A Amp Draw
  • 0.2ohms - 21A Amp Draw (RECOMMENDED LIMIT)
  • 0.1ohms - 42A Amp Draw (NOT RECOMMENDED)
  • 0.0ohms - BATTERY SHORT (DEFINITELY NOT RECOMMENDED)

Please note: This is a mechanical vape device, by pushing the fire button you complete a circuit that directly runs power from your battery through the device and into your RDA. This device does not have a chipset that you’d find in a regulated device, meaning there are no safety features apart from your own skill. We do not advise under any circumstances for a mechanical device to be used without a thorough knowledge and understanding of battery safety, battery output, Ohm’s law and vaping in general. This is a vape device for very advanced users only - this should not be used by beginners or casual vapers. If you have any questions or queries regarding mechanical devices or vaping in general, please contact us

£89.99
DOTMOD DOTBOX 200W VAPE MOD

The DotBox from DotMod is a high-quality vape device featuring a 200W Output in a sleek and trim design. Constructed of anodized Aluminium, the DotBox is powered by dual 18650 batteries (sold separately). 

The device features DotMod’s patented microprocessor that eliminates slow wattage ramp up, reliability issues, and slow recharging that are found in other processors on the market. The unique chipset ensures high performance, functionality, and reliability.

Contains: 

  • 1 x DotMod DotBox V2 200W Mod
  • 1 x USB / Lightning Charging Cable
  • 1 x User Manual
  • 1 x Authentication Certificate

Features:

  • 200W output
  • 0.08-3.0 OHM operational range
  • Proprietary dotChip technology 
  • Power locking capabilities 
  • Auto timeout button lock 
  • Multiple temperature control settings
  • 24K gold plated buttons, firing pin, and 510 
  • Magnetic door
  • Plastic encased chip set
  • Beveled edges 
  • All anodized design

Important information about Sub Ohm vaping:

This device is designed for sub-ohm vaping. It requires more vaping experience to use safely, and extra care should be taken when using a sub ohm tank. Sub Ohm coils will only work on a mod capable of firing sub ohm atomisers, and Ni200 coils will only work on devices capable of Temperature Control. Please ensure that your batteries can handle the extra power requirements and that your mod can handle the amps.

We also advise not to use any e-liquid with more than 6mg of nicotine, as your vapour may taste harsh. Sub ohm vaping produces a bigger throat hit than standard coils, and extra care should be taken.

 

Battery Type Dual 18650 Made In USA Max Wattage 200W Mod Features Temperature Control, Variable Wattage Vape Hardware Brand dotMod

Weight:143g Height:9.5cm (3.7") Width:5.5cm (2.2") Depth:2.7cm (1.1")

£149.99
DOTMOD DOTBOX 75W VAPE MOD

The DotBox from DotMod is a high-quality vape device featuring a 75W Output in a sleek and trim design. Constructed of anodized Aluminium, the DotBox is powered by a single 18650 battery (sold separately). 

The device features DotMod’s patented microprocessor that eliminates slow wattage ramp up, reliability issues, and slow recharging that are found in other processors on the market. The unique chipset ensures high performance, functionality, and reliability.

Contains: 

  • 1 x DotMod DotBox 75W Mod
  • 1 x USB / Lightning Cable
  • 1 x User Manual
  • 1 x Authentication Certificate

Features:

  • 75W output
  • 0.08-3.0 OHM operational range
  • Proprietary dotChip technology 
  • Power locking capabilities 
  • Auto timeout button lock 
  • Multiple temperature control settings
  • 24K gold plated buttons, firing pin, and 510 
  • Magnetic door
  • Plastic encased chip set
  • Beveled edges 
  • All anodized design

Important information about Sub Ohm vaping:

This device is designed for sub-ohm vaping. It requires more vaping experience to use safely, and extra care should be taken when using a sub ohm tank. Sub Ohm coils will only work on a mod capable of firing sub ohm atomisers, and Ni200 coils will only work on devices capable of Temperature Control. Please ensure that your batteries can handle the extra power requirements and that your mod can handle the amps.

We also advise not to use any e-liquid with more than 6mg of nicotine, as your vapour may taste harsh. Sub ohm vaping produces a bigger throat hit than standard coils, and extra care should be taken.

Battery Type
Single 18650
Made In
USA
Max Wattage
75W
Mod Features
Temperature Control, Variable Wattage
Vape Hardware Brand
dotMod
Weight:
98g
Height:
8.0cm (3.1")
Width:
4.3cm (1.7")
Depth:
2.2cm (0.9")
£99.99
DOTMOD PETRI TANK REPLACEMENT VAPE COILS

The dotMod Petri Tank Replacement Vape Coils are designed for use with the dotMod Petri tank, but due to a cross-compatible threading it means they can also be used in Aspire Atlantis tanks, and all other vape tanks that have this coil fitting.

Contains: 

  • 5 x dotMod Petri Replacement Vape Coils

Cross Compatible with:

  • Aspire Atlantis
  • Aspire Atlantis Evo
  • Aspire Triton
  • CCell Tanks

Important information about Sub Ohm Vaping:

These vape coils are designed for sub-ohm vaping. They require more vaping experience to use safely, and extra care should be taken when using a sub ohm tank and mod. The coils will only work on a mod capable of firing sub ohm atomisers. Please ensure that your batteries can handle the extra power requirements, and that your mod can handle the amps. 

We also advise not to use any e-liquid with more than 6mg of nicotine, as your vapour may taste harsh. Sub ohm vaping produces a bigger throat hit than standard coils, and extra care should be taken.

£15.99
DOTMOD 24MM DOTRDA

The DotRDA by dotMod, like the rest of their products, is a high-quality piece of kit that's designed to be both practical and stylish. It features a 24K gold-plated brass deck with huge clamping space, along with a revolutionary new spring-loaded design that features a single post.
Both cap and barrel are made from anodized aluminium, with interchangable pins that allow for squonk vaping. The DotRDA can be completely dissassembled without the use of a screwdriver using dotMod's patented dotKey tool.

Contains:

  • 1 x dotMod 24mm DotRDA
  • 1 x Ultem Drip Tip
  • 1 x DotKey
  • 1 x Extras (Fused Clapton Coils, Spare O-rings, Squonk Pins)

Specifications:

  • Revolutionary new spring loaded single post design 
24K gold plated brass deck
  • Adjustable airflow control 
Anodized aluminum barrel and cap
  • Interchangeable center pins for Squonking
  • 3.9mm x 1.5mm Clamping space 
 
  • Easy-drip three piece design 
4.8mm Deep Juice Well
  • Can be completely built or disassembled with the dotKey

Important information about Rebuildable Dripping Atomisers:

This product is designed for experienced users, and for those possessing an ohms reader or multimeter to test their coils on. This device requires a comprehensive understanding of the technicalities of vaping, along with knowledge of electronics and ohms law.

We don’t advise any beginners to start rebuilding coils without speaking to a knowledgeable shop. A rebuildable coil must be tested carefully on an ohms reader before it is used on a device. Not testing this properly may present a safety risk for the user, and no new coils should be used on an electronic vaping device until the coil is known to be safe.

DOTMOD PETRI V2 22MM RDA

The Dotmod Petri RDA V2 is a 22mm RDA (Rebuildable Dripping Atomiser) that includes a luxury finish and uses high quality materials. The Petri V2 features a unique build deck layout and adjustable airflow; this rebuildable atomiser is intended for advanced users only.

Quality machining and consistent build quality mean that this RDA is not only hard wearing it’s easy to assemble and disassemble. The Petri V2 features anodized aluminum construction. With gold plating on the terminal posts and build deck that increase heat conduction. Full PEEK insulation offers increased protection from overheating. Unique airflow slots allow the RDA to be adjusted to maximise flavour and cloud.

The build deck is a two post clamp deck, with one large elliptical hole on each post. This spacious deck allows for a variety of wire types to be used, including premade coils. Please note that the Petri V2 only supports dual coil builds. The post screws are easy to tighten and remove thanks to the knurling, a deep juice well provides you with ample room for eliquid.

Contains:

  • 1 x Petri V2 RDA
  • 1 x Spares Bag
  • 1 x Warranty Card

Features

  • 22mm Diameter
  • Two Post Deck
  • Dual Coil Builds Only
  • Adjustable Airflow
  • Gold Plated Deck and Posts

Important information regarding Pre-made Coils and Rebuildables:

This product is designed for experienced users, and for those possessing an ohm reader or multimeter to test their coils on.

This item requires a comprehensive understanding of the technicalities of vaping, along with knowledge of electronics and ohms law. We don’t advise any beginners to start rebuilding coils without speaking to us or a knowledgeable shop. We do not recommend using this kind of product with a mechanical mod of any kind.

A rebuildable coil must be tested carefully on an ohms reader before it is used on a device. Not testing this properly may present a safety risk for the user, and no new coils should be used on an electronic vaping device until the coil is known to be safe.

£49.99
DOTMOD PETRI 24K STANDARD VAPE TANK

The dotMod Petri 24k Standard Sub Ohm Vape Tank is a high-quality piece of kit, offering cross-compatibility with a number of existing coil ranges, including the Atlantis, Triton, and cCell series of coils.

Dotmod have chosen to plate the tank in 24k gold four times, ensuring a visually striking appearance and enhanced durability. It has a top-fill mechanism for easy refilling, as well as a threaded PEEK insulator that provides additional heat protection.

Contains:

  • 1 x dotMod Petri 24k Standard Tank
  • 1 x 0.5ohm Twisted Coil
  • 1 x 0.5ohm SS316 Coil
  • 1 x Spare Glass
  • 1 x Acrylic Drip Tip sleeve
  • 1 x Spares

Specifications:

  • 4 x 24K gold plating
  • Takes Atlantis coils as well as dotmod coil packs
  • Acrylic drip tip (prevents gunk build up)
  • Peek thermal insulation gasket
  • Brass main material
  • Adjustable airflow
  • Juice capacity of 1.9ml

Important information about Sub Ohm vaping:

This device is designed for sub-ohm vaping. It requires more vaping experience to use safely, and extra care should be taken when using a sub ohm tank. Sub Ohm coils will only work on a mod capable of firing sub ohm atomisers, and Ni200 coils will only work on devices capable of Temperature Control. Please ensure that your batteries can handle the extra power requirements, and that your mod can handle the amps.

We also advise not to use any e-liquid with more than 6mg of nicotine, as your vapour may taste harsh. Sub ohm vaping produces a bigger throat hit than standard coils, and extra care should be taken.

£49.99

Top

Panel Tool
Float header
Float topbar
Default Boxed Large Boxed Medium
Header Default Header One